Skip to content
Free delivery on orders $49+Step-by-step measuring guide30-day returns on unused, uncut items
GlassBlur

Self-adhesive soft foam

Foam Brick Wall Roll, 27.6 x 78.7 in

$26.95

A soft foam sheet with raised brick relief and recessed mortar lines that rolls out onto a smooth indoor wall and sticks in place. The padded surface gives under your thumb and casts real shadow in side light.

ColorCream

Expected delivery Thu, Nov 5 to Tue, Nov 10

  • Free shipping over $49
  • 30-day returns
Shipping and returns

Free shipping over $49. Arrives in 7-12 days. Shipping times and costs per country

Not what you were looking for? Return it within 30 days of delivery. How returns work

Specifications

Roll size
27.6 x 78.7 in (70 x 200 cm)
Covers
15.1 sq ft (1.4 m²) per roll
Material
Soft foam with a raised brick relief
Back
Self-adhesive, under peel-off release paper
Walls
Smooth, clean, dry indoor walls
Not for
Showers, stove splash zones, textured or damp walls

What you get

One roll of soft foam with a brick pattern pressed into its face and a self-adhesive back under release paper. It measures 27.6 x 78.7 in (70 x 200 cm) and covers 15.1 sq ft (1.4 m²). The foam gives under your thumb, so the wall feels padded rather than hard, and the mortar lines sit lower than the bricks, which gives the pattern real shadow when light comes from the side.

Choosing a look

  • Plain colors: Cream, Gray, Pink and Blue. Bricks and mortar share one color and the relief does the work. Calm enough for a bedroom.
  • Stone prints: Sand stone, Whitewash stone, Slate stone, Charcoal stone, Amber stone and Rust stone. A printed stacked-stone face over the same relief, made for a living room or TV wall.
  • Printed brick: Ivy, Sky, Stars, Balloons and Letters. Light brick with a pattern printed on top, for a playful corner.

Screens show colors differently, so order every roll for one wall at the same time and lay them side by side before you start.

How many rolls

Divide the wall area in square feet by 15 and round up, then add one roll for cuts. A wall 10 ft wide and 8 ft tall, 80 sq ft, takes 6 rolls, with a seventh as a spare. Hang the strips vertically. On a wall taller than 6.6 ft, start each strip at the ceiling and fill the gap at the bottom with a piece cut from another roll, matching the brick rows.

Fitting

  1. Clean the wall and let it dry. Fill holes and sand bumps so the foam sits flat.
  2. Start at a top corner. Peel back about 8 in (20 cm) of release paper, line the strip up with a level and press from the middle outward.
  3. Keep peeling and pressing on the way down. Smooth with a dry cloth so no air stays trapped.
  4. Butt the next strip tight against the first, match the brick rows and press along the seam.
  5. Trim at the ceiling, the baseboard and outlets with a sharp utility knife and a straight edge. Snap off a fresh blade often, since a dull one tears foam.

Where it works, and where it does not

Use it on smooth, dry indoor walls: bedrooms, living rooms, home offices, behind a TV or a bed. Keep it out of showers, off the wall behind a stove, and away from radiators and heaters. It will not hold on textured plaster, old wallpaper or damp walls. Foam dents if something hard hits it, so skip spots where bags and chair backs knock the wall.

Removal depends on the paint underneath. On sound paint, peel slowly at a low angle; on weak or chalky paint the adhesive may take some paint with it. If you rent, try an offcut in a hidden spot first.

Questions

Does it feel like real brick?

No, and that is part of the appeal: it is soft foam, so it is light, warm to the touch and slightly cushioned. From a few feet away the relief and print read as brick or stone, especially in side light, but up close it feels padded.

Will it stick to a textured wall?

Not reliably. The adhesive needs a smooth, flat surface for full contact. On orange-peel or knockdown texture it only touches the high points and can come away over time. Skim the wall smooth first, or choose a different wall.

How do I clean it?

Dust it with a soft brush and wipe marks with a damp cloth and a drop of mild soap, then pat it dry. Skip scouring pads and solvents, which scuff or soften foam.

Can I use it on a ceiling?

It is light enough, but long strips are awkward overhead and can sag before the adhesive grips. For ceilings, the square embossed foam ceiling tiles in this range are much easier to fit.

How do I hide the seam between two rolls?

Line up the brick rows first, then butt the edges tight without overlapping and press along the seam with a cloth. A seam that falls along a mortar line almost disappears.

GlassBlur

Shop by category

Your bag

Favorites